-40%

thorlabs ZST13 - 13 mm Stepper Motor Actuator - 1/4"-80 Thread

$ 171.6

Availability: 100 in stock
  • Brand: Thorlabs
  • All returns accepted: ReturnsNotAccepted
  • Condition: Used

    Description

    thorlabs ZST13 - 13 mm Stepper Motor Actuator - 1/4"-80 Thread .
    uggested Controller
    KIM101
    Four Output Channels, Single- or Dual-Channel Operation
    Standalone Control via Top Panel or PC-Control via USB Plug and Play
    Voltage Output from 85 V to 125 V
    Click for Details
    The control cable can be adjusted up to 110° for space-constrained applications.
    Features
    Compact Design, 31.5 mm x 17.0 mm (W x H)
    Piezo Inertia Actuator Offers 20 nm Typical Step Size
    Manual Adjustment via Rear-Located Thumbscrew
    125 V Maximum Operating Voltage
    Ø3/8" (Ø9.5 mm) Mounting Barrel with 3/8"-40 Thread on Front of Barrel
    Also Available in
    10 mm
    ,
    25 mm
    , and
    50 mm
    Travel Versions
    Ideal for Set-and-Hold Applications that Require Relative Positioning with High Resolution
    Control Cable can be Adjusted up to 110° for Space-Constrained Applications
    Thorlabs' PIA13 Piezoelectric Inertia Actuator provides high-resolution linear motion control with a long piezo-controlled translation range in a compact package. It can support loads up to 2.5 kg and preloads up to 30 N with typical movements of 20 nm and no backlash. The step size can be adjusted up to 30% to a maximum of approximately 30 nm using the KIM101 Controller and Kinesis
    ®
    software. However, due to the open-loop design, hysteresis, and application conditions, the achieved step size of the system can vary over 20%. An external feedback system will need to be used to overcome this variance.
    This actuator has a Ø3/8" mounting barrel with a 3/8"-40 thread on the front of the barrel for compatibility with our wide range of translation and rotation stages.
    For compatibility with 1/4"-80 threaded mirror mounts see our
    10 mm travel piezo inertia actuator
    . The actuator is self-locking when at rest and when there is no power supplied to the piezo, making the actuator ideal for set-and-hold applications that require nanometer resolution and long-term alignment stability. Manual adjustments can be made at any time, as long as the piezo is not actively translating the screw, by using the rear-located thumbscrew or with a 5/64" (2 mm) hex key.
    Item #
    PIA13
    Travel
    13 mm
    Typical Step Size
    a
    20 nm
    Maximum Step Size
    b
    <30 nm
    Step Size Adjustability
    c
    ≤30%
    Maximum Step Frequency
    d
    2000 Hz
    Backlash
    None
    Maximum Axial Preload
    e
    25 N
    Recommended Maximum
    Axial Load Capacity
    f
    2.5 kg (5.51 lbs)
    Velocity
    2 mm/min (Typical)
    <3.5 mm/min (Maximum)
    Drive Screw
    1/4"-80 Thread, Hard PVD Coated
    Motor Type
    Piezoelectric Inertia
    Mounting Options
    Ø3/8" (9.5 mm) Barrel
    3/8"-40
    Threaded
    Barrel
    Operating Temperature
    10 to 40 °C (50 to 104 °F)
    Dimensions
    2.34" x 1.24" x 0.67”
    (59.5 mm x 31.5 mm x 17.0 mm)
    Cable Length
    1.0 m (3.28')
    Connector
    SMC, Female
    Compatible Controller
    KIM001
    ,
    KIM101
    This value can vary over 20% due to component variance, change of direction, and application condition.
    This can be adjusted up to 30% in both directions using the KIM101 Controller and Kinesis Software.
    This can be Adjusted using the KIM101 Controller and Kinesis Software.
    Using the KIM101 Inertia Piezo Controller
    The axial force applied to the drive tip to achieve the specified step size
    . A minimum of 5 N is recommended to enhance stepping behavior.
    A higher maximum load is possible but it may adversely affect the typical step size.
    Powered by a 10 mm long
    discrete piezo stack
    , the actuator can operate at speeds of up to 3.5 mm/min. The design of the piezo motor will rotate the tip of the lead screw during translation. As shown in the image to the right, the control cable for each actuator can be rotated up to 110° for space-constrained applications.
    For information on the design of our piezo inertia "slip-stick" motor actuators, please see the complete presentation
    here
    .
    Required Controller
    The KIM101 Controller is required to operate our PIA13 Piezo Inertia Actuator; the actuator cannot be operated using a standard piezo controller. The KIM101 has an internal sawtooth voltage signal generator capable of sending sub-millisecond pulses (steps) with controllable amplitudes from 85 V to 125 V. The driver features four channels and is capable of single- or dual-channel operation, making the controller ideal for applications involving multiple motorized actuators, such as beam steering.
    For more information, please see the
    full web presentation
    .
    Condition is Used. Shipped with USPS Priority Mail.